These up down counters are monolithic complementary. MOS (CMOS) integrated circuits The CDBM and. CDBC are BCD counters while the. Details, datasheet, quote on part number: CD (CMOS) integrated circuits The CDBM and CDBC are BCD counters while the CDBM. The CDBC and CDBC up/down counters are monolithic complementary MOS (CMOS) integrated cir- cuits. The CDBC is a BCD counter.

Author: Tora Mikakasa
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Education
Published (Last): 28 November 2017
Pages: 273
PDF File Size: 1.43 Mb
ePub File Size: 8.77 Mb
ISBN: 339-7-73385-412-6
Downloads: 80021
Price: Free* [*Free Regsitration Required]
Uploader: Nekree

Up Down Counter Circuit Posted by maruf10 in forum: And yes, if you are using a switch or push-button to generate a clock you must debounce the switch. When you switch your selector switch, there is a moment when the inputs are not connected to anything, i. Thanks MrChips i’ll add up a full diagram of my Schmidt Trigger today or tomorrow, the second image was my proposed idea which you have no confirmed wouldnt be a good idea i shall return!

Your name or email address: CMOS gates especially have very high input impedances. The worst thing you can to do a CMOS input is to leave it floating. Show the complete schematic of your Schmitt Trigger circuit.

OK I have to apologies for the Rushed Diagram, I thought I had shown clearly, but after a nights sleep looking at it again it actually looks like crap ha-ha anyway I have made some modifications to the schematic, with SGT’s suggestions datwsheet the DPDT switch in its current state which I believe without de-bouncing is causing the error.


National Semiconductor

It will be floating. Nov 7, 5. Quote of the day. How to Use the Arduino Joystick Shield v2.

Of course, the one drawback with this circuit is that it requires a double-throw push-button. You have to show your schematic. Below is my suggestion to fix all of the above: If you are using TTL gates, make sure you change the resistors to 1K ohms. Nov 7, 1. Adtasheet you ask for help, it helps to be humble.

When the switch first 440192 one position or the other, the output of one of the inverters is shorted to ground. The above configuration simply never does that.


That’s why I ask for OP to show a schematic. Conversion of JK Flip-Flops This article teaches you how to convert a given JK flip-flop circuit to other types of flip-flops while verifying the process of conversion. Nov 7, 7.

Mar 14, 20, 5, Inverters as shown will also work in this application. What’s wrong with your circuit? Add K pullups on Schmitt Trigger input. Nov 7, 3. As it is, it can be anything with a floating input. There are different versions but we’ll be using v2. The values of the resistors are high enough that they present a 50uA load to the inverter output which the inverter can easily sink. The output of the latch will change state as soon as the PB is pressed and will not revert back until the opposite contact is bridged.


Nov 7, 2. Nov 7, 8.

Just to clarify; the counter increments or decrements when the up dtasheet down input transitions from 0 to 1. Nov 8, The RC filter is configured incorrectly.

National Semiconductor – datasheet pdf

Hang on a second Nov 7, 9. However, the momentary high current through the switch will xatasheet to datassheet it quite rapidly. Arguably, the situation exists only momentarily. Your CD and CU inputs are floating. Both of these have inverting outputs; but that was not shown on the diagram. The output of the inverter must be normally HIGH for this counter read the data sheet. Yes, my password is: He said he is using 2 inverters.

It shows the CU and CD both connected at the same time. Rst must be held low, and PE must be held high. Mar 24, 21, 2, The cap will help to prevent bounce. Your schematic is incorrect. Discussion in ‘ General Electronics Chat ‘ started by sni9erNov 7, It needs to be one or the other. You May Also Like: We decided to go back to the origins of AI versus human gaming.